diy upholstered wingback chair.

seriously, SWOON! I have a new favorite piece of furniture!

this project has been a long-time in the making so the fact that it is finally done is sort of a miracle. I have been interested in reupholstery for a while & completed smaller projects (upholstered lack tables HERE & our old headboard) but have been waiting to do a much bigger project.

I found this wingback chair on Craigslist almost three years ago (right after we bought our house). it was listed for $5 so we went to take a look & it was in such good shape. we gave the sellers $10 for the chair & delivery – such a good deal! then the chair sat in our basement. & it sat & sat. I finally decided on a fabric & bought it, & then had buyer’s remorse & bought another fabric. it moved with the other things into storage last spring to make way for the house renovation & then came back & sat in our living room. finally in january while aaron was on paternity leave I decided it was do or die. I had to at least start to reupholster it or I knew I never would. & three months worth of naptimes later it is finally complete!

I found lots of tutorials on Pinterest but the main ones I used are listed below:

• Basic Chair Reupholster Instruction: here & here
• Cording Tutorial: here
• Ply-Grip (Curve Ease) Tutorial: here

reupholstering is a pretty meticulous process, though you can almost always go back & do something over again if it doesn’t work out right the first time (you just have to be willing to pull out all of the staples again!). I was surprised how quickly the chair came back together since taking it apart took forever.

supplies:

• chair
• upholstery fabric – I used 6ish yards of this fabric
• staple gun & staples – we have one that attaches to our air compressor & I highly recommend that for ease of use (though it is loud to run)
• sewing machine & a zipper foot (to sew cording)
• good (fabric) scissors
• upholstery thread to match fabric – I used Coats & Clarke
• seam ripper
• piping/cording (if you don’t reuse the original)
• zipper for cushion cover (optional – you could either reuse the zipper like I did or cover the cushion without a zipper)
• tack remover
• rubber mallet – I didn’t have one of these & I wish I would have (you can also use a hammer & towel)
• needle-nose pliers
• cardboard upholstery tack strip
• upholstery tack nail strip
• Ply-Grip (Curve Ease)
• quilt batting
• upholstery dust cover (optional – I reused the original)
• camera – for taking lots of pictures as you take the chair apart!

after finding your chair & choosing your fabric, the first part of reupholstering is to un-upholster your chair. this is really time intensive as there are likely 7 million staples, plus you want to document as much as you can since you will want to put the new fabric & pieces on the exact way they came off. I took pictures as I removed pieces (hundreds of pictures which I will spare you!) but in hindsight & for a few particular places I wish I would have set up a tri-pod & videotaped those sections. just something to think about. also, as I removed pieces of fabric, I annotated on the front with a Sharpie about how it went on – like whether there was a tack strip on one side, or piping, or whatever.

{the arm rest & the wing.}

{I used a jar to contain all of the old staples. that’s a lot of staples!}

once your chair is completely stripped, you will want to check the structure for any damage. unfortunately, you may get to this point & figure out your chair isn’t worth reupholstering… that would be a bummer. hopefully you find that the structure is in good shape as well as the bottom springs, etc.

{the front & back of the chair.}

next you’ll want to cover your chair in at least one layer of batting (I did two on the wings & sides). you can also do a layer of foam underneath the batting. I didn’t because there wasn’t any originally, except for on the back upper cushion which I reused since it was in great shape. the nice thing about reupholstering, starting with batting, is that you don’t have to cut pieces exactly right. as long as there is enough material to cover the section, you can cut away any extra as you are stapling. & if you didn’t cut enough material to begin with, you can always add without there being weird seams since it will all be covered with fabric anyways.

{cutting the batting & attaching it to the chair.}

{stapling all of the batting in place.}

then you will want to lay out all of your pieces onto your new fabric & use them as patterns. if anything, you will want to cut things big because you can always trim them down. also make a note of extra cuts or jagged edges on the original pieces – these places are where the fabric had to be cut in order to fit into or around part of the chair structure & you’ll want to duplicate them as best you can. also, if you have a pattern like the one I used where you want specific parts of the fabric to be on specific parts of the chair, you’ll want to cut all of your big pieces first (lay them all out to make sure you have enough fabric) & then use the extra fabric for smaller pieces where the pattern doesn’t matter as much. for me, the front & back pieces, the front & back of the cushion cover, & the very front bottom edge of the chair where important for me to have the same floral piece centered; so I cut all of those pieces first.

{strategizing with the fabric.}

I sewed all of my piping before I really started putting the chair back together. I needed different pieces of piping along the way & I figured it would be nice to have it all done from the beginning & not have to stop & sew some together if I needed it for a certain section. I used the tutorial linked above. as long as you have a zipper foot for your machine, you are pretty much good to go. I decided against making bias strips since there weren’t a lot of curves in my chair pieces where piping would have gone. for the chair cushion I was going to do bias strips, but the original cushion didn’t have separate pieces of piping (it was part of the front & back seat fabric) so I just followed the original design. 

{supplies for piping.}

{sewing piping with the zipper foot.}

I also sewed the cushion cover at the same time I did the piping since I was into the sewing groove & needed to do piping for the cover anyways. I was able to re-use the zipper & the cushion which was helpful. down the line I may replace the cushion, but for now it works.

{sewing in the zipper & pinning the cushion pieces.}

when it came to attaching the fabric to the frame of the chair, I started with the front part of the chair. it was one of the largest pieces, but also one of the easiest to put on. from there I moved down to the bottom front edge of the chair where there was a piece that had to be sewn together (one piece was printed & wraps around the front edge, & the other piece was plain cotton muslin & ran under the cushion). I then moved to the arms of the chair. the two pieces that covered the arms had sewn pieces (the front oval shapes on the arm rests) in order to more easily attach the piping around that section I assume. because it was sewn together originally, I did the same thing when it came to reattaching. up next were the inside wings, & then the outside wings. after I did the bottom sides of the chair. the last big fabric piece was the back. lastly I did the piping that ran along the entire bottom edge, & finally the bottom dust cover (which I was able to reuse the original).

{adding the back & side pieces.}

{attaching the bottom piece.}

there are a few places that I used extra upholstery pieces to help get clean lines or edges using materials listed above. I used the cardboard tack strip (essentially a skinny piece of flexible cardstock) along the top curve of the arm rest, along the top of the piping on the inside of the chair wings, & in the top few inches of the chair back. I used the Ply-Grip (after watching the video) along the outsides of the wings, directly underneath the bottoms of the arm rests, & along the back curve of the top of the chair. & I used the tack nail strip along the top & sides of the bottom outside pieces, & along the outsides of the big back piece.

{cardboard tack strip on top of arm.}

{Ply-Grip on outside wing.}

{Ply-Grip & nail tack strip on outside bottom.}

{Ply-Grip along the back curve.}

a lot of reupholstering is just mimicking how the pieces were originally attached, so photos or video of the original chair & it’s disassembly are the most valuable in a project like this. you just have to go for it! I had to break my work over three months worth of naptimes & a few chunks of time on the weekend because of the nail gun. I could run the air compressor during eloise’s naptime & luckily the compressor doesn’t have to run the entire time you use the staple gun.

this is one of my favorite DIYs yet & now I want to reupholster everything we have in this gorgeous fabric!

have you reupholstered anything recently? I’d love to see!

M

this post contains affiliate links.